The Reese Fifth Wheel Installation Kit # RP30061 is considered a fit for your 2007 Chevrolet Silverado, and should work with Firestone Airbag suspension enhancement.
Typically the under bed mounting kits allow for utilization of the existing frame mount locations for the Firestone Airbags. The 5th wheel hitch under bed mounting kit mounts to the outside of the truck frame, and the airbag brackets typically mount on the inside of the frame. If your current Firestone Airbag System mounts... view full answer...
In most cases a front-mount hitch and a snowplow mount will install at the same points on the vehicle frame and usually they will interfere with each other. There could be a certain combination of hitch and plow that might avoid this common-mounting-point issue but it is unlikely since both items need a very strong mounting point on the vehicle in order to function. Makers of aftermarket products do not test their products fits along with other aftermarket items since there are so many... view full answer...
I spoke to my contact at B and W and she verified that from the center of where your gooseneck ball attaches to the front of the B and W Companion Slider Gooseneck to 5th Wheel Slider part # BWRVK3400 measures 15 inches. So if you were to measure from the center of your gooseneck ball forward 15 inches you would know if this would interfere with your toolbox.
You should also note that if your tool box sticks up higher than the bed rails of your truck you might see interference while making... view full answer...
I have a potential solution for you but none of the hitches for the 2007 Chevy Silverado (New Body style) are designed for models with a roll pan bumper. Installation of a hitch such as # 14301 will likely require a little trimming of the roll pan. If you are willing to make those modifications then this will work.
Otherwise you will need to look at weld-on hitches such as # 41990-07 or # 41990-16 in order to drop the receiver low enough to avoid having to trim the roll pan bumper. Weld-on... view full answer...
To determine what size brake assemblies you have you can measure the diameter of the mounted brake shoes on the trailer or measure the inside diameter of the brake drum. I am including pictures of where to measure on the brake assembly and the brake drum. You will also want to measure the width of the brake shoe lining to get the correct width brake assembly.
You will want to get the bolt pattern of the brake mounting flange on your axle and if it is a 4-bolt flange or a 5-bolt flange.... view full answer...
The only way to use the Reese M5 Series 5th Wheel Trailer Hitch part # RP30921 on a 2007 Chevrolet Silverado 2500 (New Body Style) is to install the Under-Bed Rail and Installation Kit for Reese Elite Series 5th Wheel Trailer Hitches part # RP30061. This kit provides the same underbed pucks as the Factory Ford Prep Package so it's the only option. Otherwise, you would need a new 5th wheel hitch as there isn't an adapter.
Please note, if you have a factory brake controller you will also... view full answer...
If the truck you buy does have a 3-inch hitch installed on it the Buyers Products Adapter Part # 337RTA302 would be the correct adapter as it will slide into the hitch and provide you with a 2-inch hitch.
A standard hitch pin that you would have for the 3-inch hitch would be all you need to secure the adapter like part # 58388.
Then for a pin for the 2-inch hitch you would want the part # PC3. view full answer...
The Derale # D15900 that you referenced has 8AN lines. My technical contact at Derale told me that since you have 5/16 lines on your 2007 Chevy Silverado, you should check out the Derale # D13900 because it has 5/16 lines. This is the exact same cooler as the # D15900 you referenced with the difference being the size of the lines.
Transmission coolers are not necessarily fit to a vehicle - you need to measure the open area you have for the cooler and that will determine which cooler... view full answer...
There are a few gooseneck hitches that are interchangeable between the 2002 and 2007 Chevrolet Silverado 2500HD trucks, but there are some hitches out there that were updated for the new body style change in 2007. We will need to know the brand and model number of the hitch to give you a definite answer.
If you find that you need a new gooseneck hitch, I recommend the B&W Turnoverball Gooseneck Hitch, # BWGNRK1067. B&W has been a top gooseneck hitch manufacturer and makes a quality product... view full answer...
The B&W Patriot # BWRVK3200 fits in industry standard above the bed rails the same as your Husky hitch so it will fit the same rails. If you never needed to use the slider then you should still have clearance using this hitch as well. It can actually be assembled so that the center of the hitch is 4 inches further away from the truck cab for additional clearance. view full answer...
Are you looking for a 7-way to plug into your round connector on your 2007 Chevy Silverado 1500 New Body? That's what it sounds like, and if so, use the Replacement Custom Multi-Tow 7-Way and 4-Way Trailer Connectors # 30955. view full answer...
If you have the 2007 Chevrolet Silverado New Body style, then the Curt Class III Receiver Hitch, item # 13301, that you mentioned will fit on your vehicle.
If you have the 2007 Chevrolet Silverado Classic body style the hitch you will need is the Curt Class III Square Tube Receiver Hitch, item # 13332, for your vehicle. This hitch has the same basic construction and the same weight capacities as the # 13301 hitch.
In 2007 the Silverado was built in both body styles for an extended period,... view full answer...
Access states that you can use the Vanish Roll-Up Tonneau Cover, # 834532007875, with a spray-in, over the rail bed liner. If it were a drop in over the rail bed liner you would have to trim the bed liner to install the cover. Spray-in bed liners will not have to be trimmed.
I have included a link to all of the tonneau covers for the 2007 Chevy Silverado New Body. Just select the bed type and length to see the available options. view full answer...
If you are on the Reese website, you have to search for 50064 or go through the fit guide and it will come up. The Reese Quick-Install Custom Base Rails and Installation Kit, # RP50064-58, does fit the 2007 Chevy Silverado 2500HD new body style short and long beds. I have included a link to the installation details and a link to a video showing a typical installation.
If you need a trailer hitch, for a long bed I recommend the Reese 16K, # RP30047. This is a popular hitch that performs... view full answer...
If the brake actuator on your boat trailer has an electric reverse lockout solenoid like part # T4748800 and you were using the 7-way side of the 7- and 4-Pole Trailer Connector Socket part # HM40975 then yes, the brakes would release while in reverse. However, in order to use this harness on your vehicle you will need to have a U.S. car connector plug like part # C56229 already installed. If not then you can use something like part # C57187 to release the brakes on the trailer while in... view full answer...
The HydraStar Disc Brake Kit with Actuator for Triple Axle Trailers # HSE7K-TR1 will work with the factory brake controller of your 2007 Chevy Silverado, but you'll just need an adapter, the HydraStar Electric Over Hydraulic Actuator Adapter Module for Ford and Chevy Brake Controllers # HBA-CAM.
What this adapter does is simply splice in between your trailer plug and the actuator to ensure compatibility between the actuator and brake controller. This will be all you need in order to use... view full answer...
You have a couple of options. The best thing to do would be to use a ball mount that fits in your hitch. The reason is that you will not have to worry about a reducer sleeve fitting, any capacity reduction, or adding another component in the system. For 2-1/2 inch receivers we have # RP45323 for an 18,000 pound fixed ball mount.
The other option is to use a reducer, # C45405. The hitch capacity should not be dramatically changed so if it is rated to tow the 13,000 pounds you need to tow,... view full answer...
The Center Section # C-52 for the Curt Overbed, Folding Ball Gooseneck Trailer Hitch # C61341-52 is very close to the measurements you provided. I have included an image with the measurements for this as the front to back mounting holes are 9-3/4" on center while the side to side bolts are 10" on center. As these measurements are only 1/8" different than what you found that would be roughly 1/16" for each hole so you may be able to use the plate.
Do understand it is a better idea to go... view full answer...
Yes, the B&W Custom Installation Kit w/ Base Rails # BWRVK2503 will fit your 2007 Chevrolet Silverado 1500 new body style short bed truck. You will be able to use either the 16K B&W Patriot 5th Wheel Trailer Hitch # BWRVK3200 or 18K B&W Patriot 5th Wheel Trailer Hitch # BWRVK3255 with these base rails.
Do remember that the Custom Wedge for B&W Fifth Wheels # SWW-06 is going to be needed if your trailer has a Reese Sidewinder Pin Box # RP34FR.
A Hopkins Endurance 5th Wheel/Gooseneck 90-Degree... view full answer...
Since the Firestone Ride-Rite Air Helper Springs item # F2430 uses the same fittings as the air lift kits you will be able to use the Air Lift Upgrade Kit for LoadLifter 5000 and LoadLifter 5000 Ultimate Air Helper Springs item # AL52300. With this kit you can add braided air lines to your set up.
I also recommend the Air Lift WirelessAIR Compressor System for Air Helper Springs item # AL74000EZ. Air Lift's premium, wireless, onboard compressor system with Bluetooth allows you to fill... view full answer...
Go To Results